A comparative thermodynamic analysis of Kalina and organic Rankine cycles for hot dry rock: a prospect study in the Gonghe Basin

Hot dry rock is a new type of geothermal resource which has a promising application prospect in China. This paper conducted a comparative research on performance evaluation of two eligible bottoming cycles for a hot dry rock power plant in the Gonghe Basin. Based on the given heat production conditions, a Kalina cycle and three organic Rankine cycles were tested respectively with different ammonia-water mixtures of seven ammonia mass fractions and nine eco-friendly working fluids. The results show that the optimal ammonia mass fraction is 82% for the proposed bottoming Kalina cycle in view of maximum net power output. Thermodynamic analysis suggests that wet fluids should be supercritical while dry fluids should be saturated at the inlet of turbine, respectively. The maximum net power output of the organic Rankine cycle with dry fluids expanding from saturated state is higher than that of the other organic Rankine cycle combinations, and is far higher than the maximum net power output in all tested Kalina cycle cases. Under the given heat production conditions of hot dry rock resource in the Gonghe Basin, the saturated organic Rankine cycle with the dry fluid butane as working fluid generates the largest amount of net power.     

低比转速压气机轮毂轮缘型线多目标优化设计

对电动增压器用低比转速离心压气机轮毂轮缘进行优化设计。采用NUMECA/FINE Design 3D对压气机进行几何参数化,生成数据库样本,利用人工神经网络和遗传算法对轮毂轮缘型线进行优化,并进行流场分析。仿真结果表明,在设计转速为40000 r/min时,优化后设计点压比和效率分别提高6.59%和3.73%。     

Effect of load reduction mechanisms on loads and blade bearing movements of wind turbines

The power control of wind turbines is usually realized via a change in the pitch angle of the rotor blades. Pitching facilitates the exact control of the turbines and the reliable deceleration of the rotor when required. Pitch movements can moreover be used for load control. One of these methods is called individual pitch control (IPC). IPC controls the blades individually and brings about a significant reduction in the fatigue loads and extreme loads placed on the structural components, while at the same time reducing the yield of the turbine only slightly. The lower loads reduce material costs, and thus, the cost of energy (CoE) is reduced, despite the slight reduction in yield. The method is nevertheless not used everywhere since the additional movement cycles put the rotor blade bearings in particular under stress. Special attention must be paid to small amplitude oscillating movements, which carry a high risk of inducing surface damage in the rolling contacts of the blade bearings. This paper uses a cycle analysis of the IWT7.5‐164 reference turbine to illustrate the differences in the movement patterns of wind turbine blade bearings with and without IPC. Moreover, model calculations with single contacts are used to show which of the movement patterns carries a risk of inducing surface damage. The use of IPC leads to the expected load reduction at the blade root. In current literature, IPC is usually assumed to have a negative influence on the life expectancy of blade bearings, but the findings of this study contradict this. The summed blade bearing movement is increased, although the number of very small pitch angles occurring is reduced. This reduction reduces the risk of wear in the blade bearings.     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。     

高速列车转向架构架损伤、等效应力及寿命分布特性研究

为分析高速列车转向架构架损伤、等效应力及寿命分布特性，对构架疲劳关键测点进行动应力线路实测并对测点实测时域数据波形进行解析；基于实测应力时间历程及雨流计数法编制二维应力谱，利用Goodman等寿命方程将二维应力谱等效转换为一维应力谱；阐述线性累积损伤及非线性累积损伤模型的建立方法并对实测数据的线性累积损伤及非线性累积损伤进行了计算及对比分析；分别基于线性累积损伤理论及非线性累积损伤理论推导出各理论下的等效应力，基于实测数据对两种等效应力进行了计算及对比分析；通过结合非线性累积损伤及线性累积损伤理论计算的等效应力及不同可靠度下的材料S-N曲线计算并对比分析构架结构的疲劳寿命。研究结果表明，与非线性疲劳分析理论相比，线性疲劳分析理论对高速列车转向架构架的疲劳特性评估偏于保守。     

Fatigue damage study of cold metal transition fusion-brazed aluminium/steel dissimilar joints

ABSTRACT

An aluminium/steel CMT-welded joint is mainly composed of fusion zone (FZ), interfacial intermetallic compound (IMC) zone, and heat-affected zone (HAZ). IMC and FZ are the weakest link in the welded joint. The fatigue fracture indicates that the lattice distortion caused by the lattice mismatch of Fe₂Al₅ and Fe is more likely to engender dislocation slipping and cracks easily nucleate during the fatigue testing. The hysteresis loop is shifted to the right, which indicating that the specimen experiences a ratcheting effect. In the high-stress condition, the cyclic hardening induced by the ratcheting strain is much stronger than that in the lower stress condition, which improves the fatigue life of the materials.     

Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

超疏水表面在金属防护中应用的研究进展

超疏水表面由于具有独特的微纳米粗糙结构和低表面能性质,能形成空气垫物理屏障层,减小材料表面与水或其他腐蚀介质之间的接触面积,因此被广泛应用于金属的腐蚀防护。首先简单介绍了超疏水表面的相关理论,主要包括Young氏方程、Wenzel模型和Cassie-Baxter模型。然后,归纳总结了三种制备超疏水表面的有效途径:在低表面能物质上构建微纳米级粗糙结构;先构建出具有微纳米级的粗糙结构,再对表面进行低表面能修饰;一步法完成低表面能修饰和微纳米级粗糙结构的构建。在此基础上,详细地综述了常见的超疏水表面(薄膜或涂层)在金属防护中的应用。进一步介绍了通过在超疏水体系中引入缓蚀剂的方式,构建具有主动防护功能的超疏水表面,并介绍了此种超疏水表面在金属防护中的应用。最后指出了目前的超疏水表面在制备工艺以及耐久性等方面存在的问题,并对其在金属防护领域的应用前景和发展方向作出了展望。     

热轧双相钢生产现状、存在问题及发展趋势浅析

介绍了国内外热轧双相钢的发展现状；对热轧双相钢的成分体系和关键生产工艺进行了总结，指出了目前热轧双相钢在生产过程中存在的问题；提出了未来热轧双相钢的主要发展方向为低成本、高强度、低负荷、高表面质量和“以热代冷”。     

一种镍基单晶高温合金高周疲劳引起的g′溶解行为研究

研究了一种镍基单晶高温合金SRR99在不同温度下的高周疲劳行为,试样采用[001]取向的单晶试棒。结果表明条件疲劳强度随着试验温度的升高先上升后降低,具有与高温拉伸强度表现出相同的变化规律。通过扫描电子显微镜和透射电子显微镜的观察发现g′相的形貌发生了显著变化,经过高温循环变形后g′析出相发生了溶解。在交变应力的作用下,g′与基体界面产生大量的位错,而位错的往复运动引起了g′相的溶解。因此循环加载过程中伴随着g′的不断溶解,共格界面的强化作用不断减弱。 除此之外,通过裂纹扩展方向与试样轴向的夹角可以判断出疲劳裂纹的扩展主要沿着(111)晶面进行,根据扫描电镜和透射电镜的观察结果对于循环加载的微观组织演化机理进行了讨论。